Type 1–20,000 Hz · period 2.27 ms
Start with the volume low. A steady tone, especially a high one, can be louder than it sounds and can damage hearing or a speaker tweeter. Press Space to play or stop.
440 Hz sine, 10 seconds, both channels. 44.1 kHz, 16-bit stereo.
- Set the frequency. Type a frequency in hertz (1 to 20,000 Hz), drag the slider, or tap a preset such as a guitar string or 1 kHz.
- Choose a waveform. Pick sine for a pure tone, or triangle, square or sawtooth for brighter tones with more harmonics.
- Turn the volume down and press Play. Start with the volume low, press Play, and raise it slowly to a comfortable level.
- Adjust while it plays. Fine-tune with the ±1 and ±10 Hz buttons, jump an octave, or switch the output to the left or right channel to test each speaker.
- Download it (optional). Choose a length from 1 to 60 seconds and press Download WAV to save the tone as an audio file.
Tuning by ear? The guitar string presets give you a steady reference for each open string. To tune with your microphone instead, use the Guitar Tuner; to move a whole song to another key, use the Pitch Changer.
About the Online Tone Generator
Guitar Tool Hub's free online tone generator (also called a frequency generator, sine tone generator or Hz generator) plays a steady tone at any frequency from 1 Hz to 20,000 Hz. Use it to test speakers, subwoofers and headphones, check that left and right channels are wired correctly, find the highest frequency you can hear, track down a rattle, or tune an instrument by ear against an exact pitch. Choose a sine, square, triangle or sawtooth wave, fine-tune in 1 Hz steps or jump by octaves, and read the nearest musical note as you go. Everything runs in your browser with the Web Audio API, and any tone can be downloaded as a WAV file.
- 01Play a pure tone at any frequency from 1 Hz to 20,000 Hz, to two decimal places
- 02Logarithmic frequency slider (20 Hz – 20 kHz), fine ±1 / ±10 Hz steps and one-tap octave up / down
- 034 waveforms: sine, square, triangle and sawtooth, level-matched so switching does not jump in loudness
- 04Left, both or right output for testing speakers and headphones channel by channel
- 05Shows the nearest musical note and how many cents off it the frequency is
- 06Guitar string presets (E2 A2 D3 G3 B3 E4) and common test frequencies (50 / 60 Hz hum, 440 Hz, 432 Hz, 1 kHz, 10 – 17.4 kHz)
- 07Download the tone as a WAV file (1 to 60 seconds)
- 08Change frequency, waveform, volume and output while it plays — no clicks
- 09Runs entirely in your browser — nothing to install
Frequently Asked Questions
Type a frequency in hertz or drag the slider, pick a waveform, and press Play. Start with the volume low and raise it slowly. You can change the frequency, waveform, volume and left / right output while the tone plays, and press Download WAV to save it as an audio file.
Any frequency from 1 Hz to 20,000 Hz, to two decimal places. The slider covers 20 Hz to 20 kHz, the range of human hearing, on a logarithmic scale so every octave gets the same width; type a number to go below 20 Hz. Whether you hear the very low and very high ends depends on your speakers or headphones and your ears: most laptop and phone speakers produce little below about 100 to 200 Hz.
A sine wave is a pure tone with no overtones, the smoothest and most neutral sound, and the one to use for hearing tests and speaker tests. A triangle wave adds a few soft odd harmonics and sounds a little like a flute. A square wave has strong odd harmonics and sounds hollow and buzzy, like an old video game. A sawtooth has every harmonic and sounds the brightest and harshest, like a brass or string synth. The four are level-matched here, so switching waveform does not make the tone jump in loudness.
Set Output to Left and play a tone: it should come only from the left speaker or earcup. Then switch to Right. If the sound comes from the wrong side, the channels are swapped; if it comes from both, the device is playing in mono. A tone between 200 Hz and 1 kHz is the easiest to place.
You can use it to find roughly the highest frequency you can hear: play a quiet sine wave and raise the frequency until it disappears. Most adults stop hearing somewhere between 14 and 17 kHz, and the limit falls with age. It is not a medical hearing test: the result depends on your speakers or headphones as much as your ears, and the volume is not calibrated. See an audiologist if you are worried about your hearing.
In standard tuning with A4 at 440 Hz: low E (E2) 82.41 Hz, A (A2) 110 Hz, D (D3) 146.83 Hz, G (G3) 196 Hz, B (B3) 246.94 Hz and high E (E4) 329.63 Hz. The guitar string presets play exactly these, so you can tune by ear against a steady reference tone. To tune with a microphone instead, use the Guitar Tuner.
Yes. Both are in the common frequencies list, or type any value. 432 Hz is the A that some musicians prefer to the standard 440 Hz, about 32 cents flat of it. This tool plays a tone at that frequency; it does not convert a song or audio file to 432 Hz.
Yes. Choose a length of 1, 5, 10, 30 or 60 seconds and press Download WAV. The file is a 44.1 kHz, 16-bit stereo WAV with the same frequency, waveform, volume and left / right output you are hearing, and a 10 ms fade at each end so it does not click. It is WAV rather than MP3 because MP3 encoders cut off very high frequencies and smear very pure tones.
Check the volume slider and your device volume first, then try a frequency between 200 Hz and 2 kHz, which every speaker can play. Very low tones (below about 100 Hz on phones and laptops) and very high ones (above about 15 kHz for many adults) can be inaudible even when they are playing. On an iPhone, turn off silent mode: iOS mutes web audio when the ring / silent switch is on.
Start quiet. A steady tone is more tiring to listen to than music at the same level, and a high frequency you can barely hear can still be loud enough to damage hearing or a speaker tweeter. Keep headphone volume low, take breaks, and stop if you feel discomfort or ringing in your ears.